Subversion Repositories ALCASAR

Compare Revisions

Ignore whitespace Rev 2982 → Rev 2983

/scripts/alcasar-network.sh
11,19 → 11,21
TMP_ip_gw_save="/tmp/ipset_ip_gw_save"
EXTIF=`grep ^EXTIF= $CONF_FILE|cut -d"=" -f2`
PUBLIC_IP=`grep ^PUBLIC_IP= $CONF_FILE|cut -d"=" -f2`
GW1=`grep ^GW= $CONF_FILE|cut -d"=" -f2`
MTU=`grep ^PUBLIC_MTU= $CONF_FILE|cut -d"=" -f2`
MULTIWAN=`grep ^MULTIWAN= $CONF_FILE|cut -d"=" -f2`
MULTIWAN=${MULTIWAN:=off}
NET="`ipcalc -n $PUBLIC_IP | cut -d"=" -f2`/`ipcalc -p $PUBLIC_IP | cut -d"=" -f2`"
IP=`echo $PUBLIC_IP | cut -d"/" -f1`
PRIVATE_IP_MASK=`grep ^PRIVATE_IP $CONF_FILE | cut -d"=" -f2`
PRIVATE_IP=`echo $PRIVATE_IP_MASK | cut -d"/" -f1`
PRIVATE_NETMASK=`echo $PRIVATE_IP_MASK | cut -d"/" -f2`
PRIVATE_PREFIX=`/bin/ipcalc -p $PRIVATE_IP $PRIVATE_NETMASK |cut -d"=" -f2` # prefixe du réseau (ex. 24)
PRIVATE_NETWORK=`/bin/ipcalc -n $PRIVATE_IP $PRIVATE_NETMASK| cut -d"=" -f2` # @ réseau de consultation (ex.: 192.168.182.0)
PRIVATE_NETWORK_MASK=$PRIVATE_NETWORK/$PRIVATE_PREFIX # @ + masque du réseau de consult (192.168.182.0/24)
nb_gw=`grep ^WAN $CONF_FILE | wc -l`
if [ $PUBLIC_IP != "dhcp" ]; then
GW1=`grep ^GW= $CONF_FILE|cut -d"=" -f2`
MTU=`grep ^PUBLIC_MTU= $CONF_FILE|cut -d"=" -f2`
MULTIWAN=`grep ^MULTIWAN= $CONF_FILE|cut -d"=" -f2`
MULTIWAN=${MULTIWAN:=off}
NET="`ipcalc -n $PUBLIC_IP | cut -d"=" -f2`/`ipcalc -p $PUBLIC_IP | cut -d"=" -f2`"
IP=`echo $PUBLIC_IP | cut -d"/" -f1`
PRIVATE_IP_MASK=`grep ^PRIVATE_IP $CONF_FILE | cut -d"=" -f2`
PRIVATE_IP=`echo $PRIVATE_IP_MASK | cut -d"/" -f1`
PRIVATE_NETMASK=`echo $PRIVATE_IP_MASK | cut -d"/" -f2`
PRIVATE_PREFIX=`/bin/ipcalc -p $PRIVATE_IP $PRIVATE_NETMASK |cut -d"=" -f2` # prefixe du réseau (ex. 24)
PRIVATE_NETWORK=`/bin/ipcalc -n $PRIVATE_IP $PRIVATE_NETMASK| cut -d"=" -f2` # @ réseau de consultation (ex.: 192.168.182.0)
PRIVATE_NETWORK_MASK=$PRIVATE_NETWORK/$PRIVATE_PREFIX # @ + masque du réseau de consult (192.168.182.0/24)
nb_gw=`grep ^WAN $CONF_FILE | wc -l`
fi
routecmd="ip route replace default scope global"
 
if [ $(whoami) != "root" ]; then
57,8 → 59,27
--apply)
[ -e /etc/sysconfig/network-scripts/ifcfg-$EXTIF ] && ifdown $EXTIF
# set the new configuration for EXTIF
cat <<EOF > /etc/sysconfig/network-scripts/ifcfg-$EXTIF
if [ $PUBLIC_IP == "dhcp" ]; then
cat <<EOF > /etc/sysconfig/network-scripts/ifcfg-$EXTIF
DEVICE=$EXTIF
BOOTPROTO=dhcp
DNS1=127.0.0.1
PEERDNS=no
RESOLV_MODS=yes
ONBOOT=yes
NOZEROCONF=yes
METRIC=10
MII_NOT_SUPPORTED=yes
IPV6INIT=no
IPV6TO4INIT=no
ACCOUNTING=no
USERCTL=no
MTU=$MTU
EOF
ifup $EXTIF
else
cat <<EOF > /etc/sysconfig/network-scripts/ifcfg-$EXTIF
DEVICE=$EXTIF
BOOTPROTO=static
IPADDR=$IP
NETMASK=`ipcalc -m $PUBLIC_IP | cut -d= -f2`
76,30 → 97,32
MTU=$MTU
NOZEROCONF=yes
EOF
ifup $EXTIF
ip route flush ${NET} # Remove the previous route for the network of EXTIF
ip route delete default scope global # Remove the previous default route
ip route add ${NET} dev ${EXTIF} src ${IP} # Set the new route for EXTIF network
ip route add ${NET} dev ${EXTIF} src ${IP} table 200 # Set the new default route. If no multiwan, these lines are equivalent to `ip route add default via ${GW1}`
ip route add default via ${GW1} table 200
routecmd="${routecmd} nexthop via ${GW1} dev ${EXTIF}"
ip rule flush # Remove the previous routing rules
ip rule add from all lookup main pref 32766 # Set back the main rules
ip rule add from all lookup default pref 32767 # Set back the default rules
ip rule add from ${PRIVATE_NETWORK_MASK} fwmark 200 lookup 200 # Add the rule for the first gateway
if [ "$MULTIWAN" == "on" ] || [ "$MULTIWAN" == "On" ]; then
nb_gw_supp=`grep ^WAN $CONF_FILE|wc -l`
for ((i=0 ; $i < $nb_gw_supp ; i++)); do
table=$(($i + 201)) # This number is used to mark the paquets in order to route them to the choosen GW
GW=`grep ^WAN$(($i + 1))= $CONF_FILE|awk -F'"' '{ print $2 }' | awk -F, '{print $1}'`
ip route add ${NET} dev ${EXTIF} src ${IP} table $table # Add the others route in their respective tables
ip route add default via ${GW} table $table
ip rule add from ${PRIVATE_NETWORK_MASK} fwmark $table lookup $table # Add the rule for each rule depending of the mark set by the firewall
routecmd="${routecmd} nexthop via ${GW} dev ${EXTIF}" # add the added gateway into the default gateway
done
ifup $EXTIF
ip route flush ${NET} # Remove the previous route for the network of EXTIF
ip route delete default scope global # Remove the previous default route
ip route add ${NET} dev ${EXTIF} src ${IP} # Set the new route for EXTIF network
ip route add ${NET} dev ${EXTIF} src ${IP} table 200 # Set the new default route. If no multiwan, these lines are equivalent to `ip route add default via ${GW1}`
ip route add default via ${GW1} table 200
routecmd="${routecmd} nexthop via ${GW1} dev ${EXTIF}"
ip rule flush # Remove the previous routing rules
ip rule add from all lookup main pref 32766 # Set back the main rules
ip rule add from all lookup default pref 32767 # Set back the default rules
ip rule add from ${PRIVATE_NETWORK_MASK} fwmark 200 lookup 200 # Add the rule for the first gateway
if [ "$MULTIWAN" == "on" ] || [ "$MULTIWAN" == "On" ]; then
nb_gw_supp=`grep ^WAN $CONF_FILE|wc -l`
for ((i=0 ; $i < $nb_gw_supp ; i++)); do
table=$(($i + 201)) # This number is used to mark the paquets in order to route them to the choosen GW
GW=`grep ^WAN$(($i + 1))= $CONF_FILE|awk -F'"' '{ print $2 }' | awk -F, '{print $1}'`
ip route add ${NET} dev ${EXTIF} src ${IP} table $table # Add the others route in their respective tables
ip route add default via ${GW} table $table
ip rule add from ${PRIVATE_NETWORK_MASK} fwmark $table lookup $table # Add the rule for each rule depending of the mark set by the firewall
routecmd="${routecmd} nexthop via ${GW} dev ${EXTIF}" # add the added gateway into the default gateway
done
fi
${routecmd} # define the default gateway for outgoing traffic
ip route flush cache
fi
${routecmd} # define the default gateway for outgoing traffic
ip route flush cache
/usr/local/bin/alcasar-iptables.sh
exit 0
;;
*)