Subversion Repositories ALCASAR

#!/bin/bash

# $Id: alcasar-iptables.sh 3040 2022-07-17 22:31:53Z rexy $

# Script de mise en place des regles du parefeu d'Alcasar (mode normal)

# This script writes the netfilter rules for ALCASAR

# Rexy - 3abtux - CPN

#

# Reminders

# There are four channels for log :

#	1 tracability of the consultation equipment with The 'Netflow' kernel module (iptables target = NETFLOW);

#	2 protection of ALCASAR with the Ulog group 1 (default group)

#	3 SSH on ALCASAR with the Ulog group 2;

#	4 extern access attempts on ALCASAR with the Ulog group 3.

# The bootps/dhcp (67) port is always open on tun0/INTIF by coova

CONF_FILE="/usr/local/etc/alcasar.conf"

EXTIF=`grep ^EXTIF= $CONF_FILE|cut -d"=" -f2`				# EXTernal InterFace

INTIF=`grep ^INTIF= $CONF_FILE|cut -d"=" -f2`				# INTernal InterFace

TUNIF="tun0"								# listen device for chilli daemon

private_ip_mask=`grep ^PRIVATE_IP= $CONF_FILE|cut -d"=" -f2`

private_ip_mask=${private_ip_mask:=192.168.182.1/24}

PRIVATE_IP=`echo $private_ip_mask | cut -d"/" -f1`			# ALCASAR LAN IP address

private_network=`/bin/ipcalc -n $private_ip_mask|cut -d"=" -f2`		# LAN IP address (ie.: 192.168.182.0)

private_prefix=`/bin/ipcalc -p $private_ip_mask|cut -d"=" -f2`		# LAN prefix (ie. 24)

PRIVATE_NETWORK_MASK=$private_network/$private_prefix			# Lan IP address + prefix (192.168.182.0/24)

public_ip_mask=`grep ^PUBLIC_IP= $CONF_FILE|cut -d"=" -f2`		# ALCASAR WAN IP address

if [[ "$public_ip_mask" == "dhcp" ]]

then

	PTN="\b(25[0-5]|2[0-4][0-9]|[01]?[0-9][0-9]?)\.(25[0-5]|2[0-4][0-9]|[01]?[0-9][0-9]?)\.(25[0-5]|2[0-4][0-9]|[01]?[0-9][0-9]?)\.(25[0-5]|2[0-4][0-9]|[01]?[0-9][0-9]?)\/([012]?[0-9]|3[0-2])\b"

	public_ip_mask=`ip addr show $EXTIF | egrep -o $PTN`

fi

PUBLIC_IP=`echo $public_ip_mask | cut -d"/" -f1`

dns1=`grep ^DNS1= $CONF_FILE|cut -d"=" -f2`

dns2=`grep ^DNS2= $CONF_FILE|cut -d"=" -f2`

dns1=${dns1:=208.67.220.220}

dns2=${dns2:=208.67.222.222}

DNSSERVERS="$dns1,$dns2"						# first and second public DNS servers

INT_DNS_IP=`grep INT_DNS_IP $CONF_FILE|cut -d"=" -f2`			# Adresse du serveur DNS interne

INT_DNS_ACTIVE=`grep INT_DNS_ACTIVE $CONF_FILE|cut -d"=" -f2`	# Activation de la redirection DNS interne

BL_IP_CAT="/usr/local/share/iptables-bl-enabled"			# categories files of the BlackListed IP

WL_IP_CAT="/usr/local/share/iptables-wl-enabled"			# categories files of the WhiteListed IP

TMP_users_set_save="/tmp/users_set_save"				# tmp file for backup users set

TMP_set_save="/tmp/ipset_save"						# tmp file for blacklist and whitelist creation

TMP_ip_gw_save="/tmp/ipset_ip_gw_save"				# tmp file for already connected ips

SSH=`grep ^SSH= $CONF_FILE|cut -d"=" -f2`				# sshd active (on/off)

SSH=${SSH:=off}

SSH_PORT=`grep ^SSH_WAN= $CONF_FILE|cut -d"=" -f2`		#ssh WAN port

SSH_PORT=${SSH_PORT:=0}

SSH_ADMIN_FROM=`grep ^SSH_ADMIN_FROM= $CONF_FILE|cut -d"=" -f2`

SSH_ADMIN_FROM=${SSH_ADMIN_FROM:="0.0.0.0/0.0.0.0"}			# WAN IP address to reduce ssh access (all ip allowed on LAN side)

IPTABLES="/sbin/iptables"

IP_REHABILITEES="/etc/e2guardian/lists/exceptioniplist"		# Rehabilitated IP

SITE_DIRECT="/usr/local/etc/alcasar-site-direct"			# WEB Sites allowed for all (no av and no filtering for av_bl users)

MULTIWAN=`grep ^MULTIWAN $CONF_FILE|cut -d"=" -f2`

PROXY=`grep ^PROXY= $CONF_FILE|cut -d"=" -f2`

PROXY_IP=`grep ^PROXY_IP= $CONF_FILE|cut -d"=" -f2`

nb_gw=`grep ^WAN $CONF_FILE|wc -l`

HOST=`grep ^HOSTNAME= $CONF_FILE|cut -d"=" -f2`

DOM=`grep ^DOMAIN= $CONF_FILE|cut -d"=" -f2`

DOMAIN="$HOST.$DOM"

# Allow requests to internal DNS if activated

if [ "$INT_DNS_ACTIVE" = "on" ]

then

	DNSSERVERS="$DNSSERVERS,$INT_DNS_IP"

fi

#ipset name list for load_balancing

gw_list="gw0"

if [ "$MULTIWAN" == "on" ] || [ "$MULTIWAN" == "On" ]; then

	for ((i=1 ; i<=$nb_gw ; i++)); do

		gw_list="${gw_list} gw$i"

	done

fi

# Sauvegarde des SET des utilisateurs connectés si ils existent

# Saving SET of connected users if it exists

ipset list not_filtered 1>/dev/null 2>&1

if [ $? -eq 0 ];

then

	ipset save not_filtered > $TMP_users_set_save

	ipset save av >> $TMP_users_set_save

	ipset save av_bl >> $TMP_users_set_save

	ipset save av_wl >> $TMP_users_set_save

	ipset save proto_0 >> $TMP_users_set_save

	ipset save proto_1 >> $TMP_users_set_save

	ipset save proto_2 >> $TMP_users_set_save

	ipset save proto_3 >> $TMP_users_set_save

fi

# Sauvegarde de la liste de toutes les IP déjà connectées pour les réintégrer dans le load balancing

# Saving all of the already connected IP in order to put them back in the load balancing after

if [ ! -f $TMP_ip_gw_save ];then

	# Save only if alcasar-network.sh --save has not been executed before

	for i in $gw_list;do

		ipset list $i 1>/dev/null 2>&1

		if [ $? -eq 0 ]

		then

			# the cut -d":" -f5 deletes all the lines with a :, i.e all the lines execpt the members

			ipset list $i | cut -d":" -f5 | sed '/^[[:space:]]*$/d' >> $TMP_ip_gw_save

		fi

	done

fi

# Chargement de la sonde NetFlow (module noyau ipt_NETFLOW)

# loading of NetFlow probe (ipt_NETFLOW kernel module)

modprobe ipt_NETFLOW destination=127.0.0.1:2055

# Effacement des règles existantes

# Flush all existing rules

$IPTABLES -F

$IPTABLES -t nat -F

$IPTABLES -t mangle -F

$IPTABLES -F INPUT

$IPTABLES -F FORWARD

$IPTABLES -F OUTPUT

# Suppression des chaines utilisateurs sur les tables filter et nat

# Flush non default rules on filter and nat tables

$IPTABLES -X

$IPTABLES -t nat -X

# Stratégies par défaut

# Default policies

$IPTABLES -P INPUT DROP

$IPTABLES -P FORWARD DROP

$IPTABLES -P OUTPUT DROP

$IPTABLES -t nat -P PREROUTING ACCEPT

$IPTABLES -t nat -P POSTROUTING ACCEPT

$IPTABLES -t nat -P OUTPUT ACCEPT

#############################

#          IPSET            #

#############################

# destruction de tous les SET

# destroy all SET

ipset flush

ipset destroy

###### BL set  ###########

# Calcul de la taille / Compute the length

bl_set_length=$(wc -l $BL_IP_CAT/* | awk '{print $1}' | tail -n 1)

# Chargement / loading

echo "create bl_ip_blocked hash:net family inet hashsize 1024 maxelem $bl_set_length" > $TMP_set_save

for category in `ls -1 $BL_IP_CAT | cut -d '@' -f1`

do

	cat $BL_IP_CAT/$category >> $TMP_set_save

done

ipset -! restore < $TMP_set_save

rm -f $TMP_set_save

# Suppression des ip réhabilitées / Removing of rehabilitated ip

for ip in $(cat $IP_REHABILITEES)

do

	ipset -q del bl_ip_blocked $ip

done

# ipset for exception web sites (usefull for filtered users = av_bl)

ipset create site_direct hash:net hashsize 1024

for site in $(cat $SITE_DIRECT)

do

    ipset add site_direct $site

done

###### WL set  ###########

# taille fixe, car peuplé par dnsmasq / fixe length due to dnsmasq dynamic loading

wl_set_length=65536

# Chargement Loading

echo "create wl_ip_allowed hash:net family inet hashsize 1024 maxelem $wl_set_length" > $TMP_set_save

#get ip-wl files from ACC

for category in `ls -1 $WL_IP_CAT |cut -d '@' -f1`

do

	cat $WL_IP_CAT/$category >> $TMP_set_save

done

ipset -! restore < $TMP_set_save

rm -f $TMP_set_save

# Restoration des SET des utilisateurs connectés si ils existent sinon création des SET

# Restoring the connected users SETs if available, otherwise creating SETs

if [ -e $TMP_users_set_save ];

then

	ipset -! restore < $TMP_users_set_save

	rm -f $TMP_users_set_save

else

	ipset create not_filtered hash:ip hashsize 1024

	ipset create av hash:ip hashsize 1024

	ipset create av_bl hash:ip hashsize 1024

	ipset create av_wl hash:ip hashsize 1024

	# pour les filtrages de protocole par utilisateur / For network protocols filtering by user

	ipset create proto_0 hash:ip hashsize 1024

	ipset create proto_1 hash:ip hashsize 1024

	ipset create proto_2 hash:ip hashsize 1024

	ipset create proto_3 hash:ip hashsize 1024

fi

#ipsets for load balancing

for i in $gw_list; do

	ipset create $i hash:ip

done

cat $TMP_ip_gw_save | while read ip; do

	gw_min="gw0"

	weight=`grep ^PUBLIC_WEIGHT= $CONF_FILE | cut -d"=" -f2`

	already=`ipset list $gw_min | grep Number\ of\ entries: | cut -d":" -f2`

	#The *1000 is here to avoid working on floats in bash

	gw_min_value=$((1000 * $already / $weight))

	i=1

	for gw in $gw_list;do

		if [ "$gw" != "gw0" ]; then

			weight=`grep ^WAN$i= $CONF_FILE | awk -F'"' '{ print $2 }' | awk -F ',' '{ print $2 }'`

			already=`ipset list $gw | grep Number\ of\ entries: | cut -d":" -f2`

			value=$((1000 * $already / $weight))

			if [ $value -lt $gw_min_value ]

			then

				gw_min_value=$value

				gw_min=$gw

			fi

			i=$(($i+1))

		fi

	done

	ipset add $gw_min $ip

done

rm -f $TMP_ip_gw_save

#############################

#       PREROUTING          #

#############################

# Marquage (et journalisation) des paquets qui tentent d'accéder directement aux ports d'écoute du proxy HTTP/HTTPS (E2Guardian) pour pouvoir les rejeter en INPUT

# Mark (and log) the direct attempts to E2guardian listen ports in order to REJECT them in INPUT rules

# 8080 = ipset av_bl

$IPTABLES -A PREROUTING -t nat -i $TUNIF -p tcp -d $PRIVATE_IP -m tcp --dport 8080 -j NFLOG --nflog-group 1 --nflog-prefix "RULE direct-proxy -- DENY "

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p tcp -m tcp --dport 8080 -j MARK --set-mark 1

# 8090 = ipset av_wl + av

$IPTABLES -A PREROUTING -t nat -i $TUNIF -p tcp -d $PRIVATE_IP -m tcp --dport 8090 -j NFLOG --nflog-group 1 --nflog-prefix "RULE direct-proxy -- DENY "

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p tcp -m tcp --dport 8090 -j MARK --set-mark 2

# 8443 = tranparent HTTPS for ipsets av_bl + av_wl + av (future version)

#$IPTABLES -A PREROUTING -t nat -i $TUNIF -p tcp -d $PRIVATE_IP -m tcp --dport 8443 -j NFLOG --nflog-group 1 --nflog-prefix "RULE direct-proxy -- DENY "

#$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p tcp -m tcp --dport 8443 -j MARK --set-mark 6

# Marquage des paquets qui tentent d'accéder directement aux ports d'écoute DNS (UNBOUND) pour pouvoir les rejeter en INPUT

# Mark the direct attempts to DNS ports (UNBOUND) in order to REJECT them in INPUT rules

# 54 = ipset av_bl

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p tcp --dport 54 -j MARK --set-mark 3

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p udp --dport 54 -j MARK --set-mark 3

# 55 = ipset av_wl

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p tcp --dport 55 -j MARK --set-mark 4

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p udp --dport 55 -j MARK --set-mark 4

# 56 = blackall

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p tcp --dport 56 -j MARK --set-mark 5

$IPTABLES -A PREROUTING -t mangle -i $TUNIF -d $PRIVATE_IP -p udp --dport 56 -j MARK --set-mark 5

# redirection DNS des usagers

# users DNS redirection

# 54 = ipset av_bl

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_bl src -p udp --dport domain -j REDIRECT --to-port 54

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_bl src -p tcp --dport domain -j REDIRECT --to-port 54

# 55 = ipset av_wl

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_wl src -p udp --dport domain -j REDIRECT --to-port 55

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_wl src -p tcp --dport domain -j REDIRECT --to-port 55

# 53 = all other users

$IPTABLES -A PREROUTING -t nat -i $TUNIF ! -d $PRIVATE_IP -p udp --dport domain -j REDIRECT --to-port 53

$IPTABLES -A PREROUTING -t nat -i $TUNIF ! -d $PRIVATE_IP -p tcp --dport domain -j REDIRECT --to-port 53

# Redirection HTTP des usagers 'av_bl' cherchant à joindre les IP de la blacklist vers ALCASAR (page 'accès interdit')

# Redirect HTTP of 'av_bl' users who want blacklist IP to ALCASAR ('access denied' page)

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_bl src -m set --match-set bl_ip_blocked dst -p tcp --dport http -j REDIRECT --to-port 80

# Redirection HTTP des usagers 'av_wl' cherchant à joindre les IP qui ne sont pas dans la WL vers ALCASAR (page 'accès interdit')

# Redirect HTTP of 'av_wl' users who want IP not in the WL to ALCASAR ('access denied' page)

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_wl src -m set ! --match-set wl_ip_allowed dst -p tcp --dport http -j REDIRECT --to-port 80

# Journalisation des usagers "av_bl + av_wl + av" (paquets SYN uniquement). Les autres protocoles sont journalisés en FORWARD par netflow.

# accounting of "av_bl + av_wl + av"  users (only syn packets). Other protocols are logged in FORWARD by netflow

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_bl src ! -d $PRIVATE_IP -p tcp --dport http -m conntrack --ctstate NEW -j NFLOG --nflog-group 1 --nflog-prefix "RULE F_http -- ACCEPT "

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_wl src ! -d $PRIVATE_IP -p tcp --dport http -m conntrack --ctstate NEW -j NFLOG --nflog-group 1 --nflog-prefix "RULE F_http -- ACCEPT "

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av src ! -d $PRIVATE_IP -p tcp --dport http -m conntrack --ctstate NEW -j NFLOG --nflog-group 1 --nflog-prefix "RULE F_http -- ACCEPT "

# Redirection des requêtes HTTP des usagers "av_bl + av_wl + av" vers E2guardian

# Redirect outbound "av_bl + av_wl +av" users HTTP requests to E2guardian

# 8080 = ipset av_bl

#$IPTABLES -A PREROUTING -t mangle -i $TUNIF -m set --match-set av_bl src -m set ! --match-set site_direct dst ! -d $PRIVATE_IP  -p tcp --dport http -j MARK --set-mark 200

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_bl src -m set ! --match-set site_direct dst ! -d $PRIVATE_IP  -p tcp --dport http -j REDIRECT --to-port 8080

# 8090 = ipset av_wl & av

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_wl src ! -d $PRIVATE_IP -p tcp --dport http -j REDIRECT --to-port 8090

$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av src ! -d $PRIVATE_IP -p tcp --dport http -j REDIRECT --to-port 8090

# Redirection des requêtes HTTPS sortantes des usagers av_bl + av_wl + av vers E2Guardian (in a future version - don't forget to set E2guardian as a tranparent HTTPS proxy)

# Redirect outbound HTTPS requests of av_bl + av_wl + av users to E2Guardian

#$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_bl src -m set ! --match-set site_direct dst ! -d $PRIVATE_IP  -p tcp --dport https -j REDIRECT --to-port 8443

#$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av_wl src -m set ! --match-set site_direct dst ! -d $PRIVATE_IP  -p tcp --dport https -j REDIRECT --to-port 8443

#$IPTABLES -A PREROUTING -t nat -i $TUNIF -m set --match-set av src -m set ! --match-set site_direct dst ! -d $PRIVATE_IP  -p tcp --dport https -j REDIRECT --to-port 8443

# Redirection des requêtes NTP vers le serveur NTP local

# Redirect NTP request in local NTP server

$IPTABLES -A PREROUTING -t nat -i $TUNIF -s $PRIVATE_NETWORK_MASK ! -d $PRIVATE_IP -p udp --dport ntp -j REDIRECT --to-port 123

#Récupération de la marque associée à une gw pour chaque connection

$IPTABLES -A PREROUTING -t mangle -j CONNMARK --restore-mark

if [ "$PROXY" == "on" ] || [ "$PROXY" == "On" ];then

	$IPTABLES -A PREROUTING -t nat -i $TUNIF ! -d $PRIVATE_IP -p tcp -m multiport --dports http,https -j DNAT --to-destination $PROXY_IP

fi

#Marquage pour le load balancing

if [ "$MULTIWAN" == "on" ] || [ "$MULTIWAN" == "On" ]; then

	temp_index=200

	for i in $gw_list; do

		$IPTABLES -A PREROUTING -t mangle -i $TUNIF -m set --match-set $i src -j MARK --set-mark $temp_index

		temp_index=$(($temp_index+1))

	done

fi

#############################

#         INPUT             #

#############################

# Tout passe sur loopback

# accept all on loopback

$IPTABLES -A INPUT -i lo -j ACCEPT

$IPTABLES -A OUTPUT -o lo -j ACCEPT

# Rejet des demandes de connexions non conformes (FIN-URG-PUSH, XMAS, NullScan, SYN-RST et NEW not SYN)

# Drop non standard connexions (FIN-URG-PUSH, XMAS, NullScan, SYN-RST and NEW not SYN)

$IPTABLES -A INPUT -p tcp --tcp-flags FIN,URG,PSH FIN,URG,PSH -j DROP

$IPTABLES -A INPUT -p tcp --tcp-flags ALL ALL -j DROP

$IPTABLES -A INPUT -p tcp --tcp-flags ALL NONE -j DROP

$IPTABLES -A INPUT -p tcp --tcp-flags SYN,RST SYN,RST -j DROP

$IPTABLES -A INPUT -p tcp -m tcp ! --syn -m conntrack --ctstate NEW -j DROP

# Si configéré, on autorise les réponses DHCP

# Allow DHCP answers if configured

public_ip_mask=`grep ^PUBLIC_IP= $CONF_FILE|cut -d"=" -f2`		# ALCASAR WAN IP address

if [[ "$public_ip_mask" == "dhcp" ]]

then

	$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport 68 -j ACCEPT

	$IPTABLES -A OUTPUT -o $EXTIF -p udp --dport 68 -j ACCEPT

fi

# On rejette les trame en broadcast et en multicast sur EXTIF (évite leur journalisation)

# Drop broadcast & multicast on EXTIF to avoid log

$IPTABLES -A INPUT -m addrtype --dst-type BROADCAST,MULTICAST -j DROP

# On autorise les retours de connexions légitimes par INPUT

# Conntrack on INPUT

$IPTABLES -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT

# On interdit les connexions directes aux ports d'écoute d'E2Guardian. Les packets concernés ont été marqués et loggués dans la table mangle (PREROUTING)

# Deny direct connections on E2Guardian listen ports. The concerned paquets have been marked and logged in mangle table (PREROUTING)

$IPTABLES -A INPUT -i $TUNIF -p tcp --dport 8080 -m mark --mark 1 -j REJECT --reject-with tcp-reset # av_bl

$IPTABLES -A INPUT -i $TUNIF -p tcp --dport 8090 -m mark --mark 2 -j REJECT --reject-with tcp-reset # av_wl + av

#$IPTABLES -A INPUT -i $TUNIF -p tcp --dport 8443 -m mark --mark 6 -j REJECT --reject-with tcp-reset # av_bl + av_wl + av (future version)

# On autorise les connexions HTTP/HTTPS légitimes vers E2Guardian

# Allow HTTP connections to E2Guardian

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -p tcp --dport 8080 -m conntrack --ctstate NEW --syn -j ACCEPT

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -p tcp --dport 8090 -m conntrack --ctstate NEW --syn -j ACCEPT

#$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -p tcp --dport 8443 -m conntrack --ctstate NEW --syn -j ACCEPT # (future version)

# On interdit les connexions directes aux ports d'écoupe DNS (UNBOUND). Les packets concernés ont été marqués dans la table mangle (PREROUTING)

# Deny direct connections to DNS ports (UNBOUND). The concerned paquets are marked in mangle table (PREROUTING)

$IPTABLES -A INPUT -i $TUNIF -p udp --dport 54 -m mark --mark 3 -j REJECT --reject-with icmp-port-unreachable

$IPTABLES -A INPUT -i $TUNIF -p tcp --dport 54 -m mark --mark 3 -j REJECT --reject-with tcp-reset

$IPTABLES -A INPUT -i $TUNIF -p udp --dport 55 -m mark --mark 4 -j REJECT --reject-with icmp-port-unreachable

$IPTABLES -A INPUT -i $TUNIF -p tcp --dport 55 -m mark --mark 4 -j REJECT --reject-with tcp-reset

$IPTABLES -A INPUT -i $TUNIF -p udp --dport 56 -m mark --mark 5 -j REJECT --reject-with icmp-port-unreachable

$IPTABLES -A INPUT -i $TUNIF -p tcp --dport 56 -m mark --mark 5 -j REJECT --reject-with tcp-reset

# On autorise les connexion DNS légitime

# Allow DNS connections

# ipset = av_bl

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p udp --dport 54 -j ACCEPT

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport 54 -j ACCEPT

# ipset = av_wl

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p udp --dport 55 -j ACCEPT

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport 55 -j ACCEPT

# blackall

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p udp --dport 56 -j ACCEPT

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport 56 -j ACCEPT

# On accepte l'accès aux services internes

# Internal services access

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p udp --dport domain -j ACCEPT	# DNS

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport domain -j ACCEPT	# DNS

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p icmp --icmp-type 8 -j ACCEPT	# Réponse ping # ping responce

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p icmp --icmp-type 0 -j ACCEPT	# Requête  ping # ping request

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport https -j ACCEPT	# Pages d'authentification et MCC # authentication pages and MCC

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport http -j ACCEPT	# Page d'avertissement filtrage # Filtering warning pages

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport 3990:3991 -j ACCEPT	# Requêtes de deconnexion usagers # Users logout requests

$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p udp --dport ntp -j ACCEPT	# Serveur local de temps # local time server

# Accès au serveur SSHD si activé

# SSHD server access if enabled

if [ $SSH = on ]

	then

	$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport ssh -m conntrack --ctstate NEW -j NFLOG --nflog-group 2 --nflog-prefix "RULE ssh-from-LAN -- ACCEPT"

	$IPTABLES -A INPUT -i $TUNIF -s $PRIVATE_NETWORK_MASK -d $PRIVATE_IP -p tcp --dport ssh -j ACCEPT

	if [ $SSH_PORT -gt 0 ]

		then

		$IPTABLES -A INPUT -i $EXTIF -s $SSH_ADMIN_FROM -d $PUBLIC_IP -p tcp --dport $SSH_PORT -m conntrack --ctstate NEW --syn -j NFLOG --nflog-group 2 --nflog-prefix "RULE ssh-from-WAN -- ACCEPT"

		$IPTABLES -A INPUT -i $EXTIF -s $SSH_ADMIN_FROM -d $PUBLIC_IP -p tcp --dport $SSH_PORT -m conntrack --ctstate NEW -j ACCEPT

	fi

fi

# Insertion de règles locales

# Here, we add local rules (i.e. VPN from Internet)

if [ -f /usr/local/etc/alcasar-iptables-local.sh ]; then

	. /usr/local/etc/alcasar-iptables-local.sh

fi

# Journalisation et rejet des connexions (autres que celles autorisées) effectuées depuis le LAN

# Deny and log on INPUT from the LAN

$IPTABLES -A INPUT -i $TUNIF -m conntrack --ctstate NEW -j NFLOG --nflog-group 3 --nflog-prefix "RULE rej-int -- REJECT "

$IPTABLES -A INPUT -i $TUNIF -p tcp -j REJECT --reject-with tcp-reset

$IPTABLES -A INPUT -i $TUNIF -p udp -j REJECT --reject-with icmp-port-unreachable

# Interdiction d'accès à INTIF (n'est utile que lorsque chilli est arrêté).

# Reject INTIF access (only when chilli is down)

$IPTABLES -A INPUT -i $INTIF -j NFLOG --nflog-group 3 --nflog-prefix "RULE Protect1 -- REJECT "

$IPTABLES -A INPUT -i $INTIF -j REJECT

# Journalisation et rejet des connexions initiées depuis le réseau extérieur (test des effets du paramètre --limit en cours)

# On EXTIF, the access attempts are log in channel 2 (we should test --limit option to avoid deny of service)

$IPTABLES -A INPUT -i $EXTIF -m conntrack --ctstate NEW -j NFLOG --nflog-group 3 --nflog-threshold 10 --nflog-prefix "RULE rej-ext -- DROP"

#############################

#        FORWARD            #

#############################

# Blocage des IPs du SET bl_ip_blocked pour le SET av_bl

# Deny IPs of the SET bl_ip_blocked for the set av_bl

$IPTABLES -A FORWARD -i $TUNIF -m set --match-set av_bl src -m set --match-set bl_ip_blocked dst -p icmp -j REJECT --reject-with icmp-host-prohibited

$IPTABLES -A FORWARD -i $TUNIF -m set --match-set av_bl src -m set --match-set bl_ip_blocked dst -p udp -j REJECT --reject-with icmp-host-prohibited

$IPTABLES -A FORWARD -i $TUNIF -m set --match-set av_bl src -m set --match-set bl_ip_blocked dst -p tcp -j REJECT --reject-with tcp-reset

# Active le suivi de session

# Allow Conntrack

$IPTABLES -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT

# Compute uamallowed IP (ie : IP address of equipments connected between ALCASAR and router like DMZ, own servers, etc.)

nb_uamallowed=`wc -l /usr/local/etc/alcasar-uamallowed | cut -d" "  -f1`

if [ $nb_uamallowed != "0" ]

then

	while read ip_allowed_line

	do

		ip_allowed=`echo $ip_allowed_line|cut -d"\"" -f2`

		$IPTABLES -A FORWARD -i $TUNIF -d $ip_allowed -m conntrack --ctstate NEW -j NETFLOW

		$IPTABLES -A FORWARD -i $TUNIF -d $ip_allowed -m conntrack --ctstate NEW -j ACCEPT

	done < /usr/local/etc/alcasar-uamallowed

fi

# filtrage protocole par utilisateur (profile 1 : http, https)

# protocols filtering for users (profil 1 : http, https)

	$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_1 src -s $PRIVATE_NETWORK_MASK -p tcp -m multiport ! --dports http,https -m conntrack --ctstate NEW -j REJECT --reject-with tcp-reset

	$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_1 src -s $PRIVATE_NETWORK_MASK -p udp -m multiport ! --dports http,https -m conntrack --ctstate NEW -j REJECT --reject-with icmp-port-unreachable

# filtrage protocole par utilisateur (profile 2 : http https smtp pop3 pop3s imap imaps ftp sftp ssh)

# protocols filtering for users (profil 2 : http https smtp pop3 pop3s imap imaps ftp sftp ssh)

	$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_2 src -s $PRIVATE_NETWORK_MASK -p tcp -m multiport ! --dports smtp,http,https,pop3,pop3s,imap,imaps,ftp,ftp-data,sftp,ssh -m conntrack --ctstate NEW -j REJECT --reject-with tcp-reset

	$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_2 src -s $PRIVATE_NETWORK_MASK -p udp -m multiport ! --dports smtp,http,https,pop3,pop3s,imap,imaps,ftp,ftp-data,sftp,ssh -m conntrack --ctstate NEW -j REJECT --reject-with icmp-port-unreachable

# filtrage protocole par utilisateur (profile 3 : personnalisable via l'ACC)

# protocols filtering for users (profil 3 : customized with ACC)

custom_tcp_protocols_list='';custom_udp_protocols_list=''

while read svc_line

do

	svc_on=`echo $svc_line|cut -b1`

	if [ $svc_on != "#" ]

	then

		svc_name=`echo $svc_line|cut -d" " -f1`

		svc_port=`echo $svc_line|cut -d" " -f2`

		if [ $svc_name = "icmp" ]

		then

			svc_icmp="on"

		else

			if [ "$custom_tcp_protocols_list" == "" ]

			then

				custom_tcp_protocols_list=$svc_port

			else

				custom_tcp_protocols_list=`echo $custom_tcp_protocols_list","$svc_port`

			fi

			udp_svc=`egrep "[[:space:]]$svc_port/udp" /etc/services|wc -l`

			if [ $udp_svc = "1" ] # udp service exist

			then

				if [ "$custom_udp_protocols_list" == "" ]

				then

					custom_udp_protocols_list=$svc_port

				else

					custom_udp_protocols_list=`echo $custom_udp_protocols_list","$svc_port`

				fi

			fi

		fi

	fi

done < /usr/local/etc/alcasar-services

	if [ "$custom_tcp_protocols_list" == "" ]

	then

		$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_3 src -s $PRIVATE_NETWORK_MASK -j REJECT

	else

		if [ "$svc_icmp" != "on" ]

		then

			$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_3 src -s $PRIVATE_NETWORK_MASK -p icmp -j REJECT --reject-with icmp-proto-unreachable

		fi

		$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_3 src -s $PRIVATE_NETWORK_MASK -p tcp -m multiport ! --dports $custom_tcp_protocols_list -m conntrack --ctstate NEW -j REJECT --reject-with tcp-reset

		$IPTABLES -A FORWARD -i $TUNIF -m set --match-set proto_3 src -s $PRIVATE_NETWORK_MASK -p udp -m multiport ! --dports $custom_udp_protocols_list -m conntrack --ctstate NEW -j REJECT --reject-with icmp-port-unreachable

	fi

# Blocage des usagers 'av_wl' cherchant à joindre les IP qui ne sont pas dans la WL

# Block 'av_wl' users who want IP not in the WL

$IPTABLES -A FORWARD -i $TUNIF -m set --match-set av_wl src -m set ! --match-set wl_ip_allowed dst -j DROP

# journalisation et autorisation des connections sortant du LAN

# Allow forward connections with log

$IPTABLES -A FORWARD -i $TUNIF -s $PRIVATE_NETWORK_MASK -m conntrack --ctstate NEW -j NETFLOW

$IPTABLES -A FORWARD -i $TUNIF -s $PRIVATE_NETWORK_MASK -m conntrack --ctstate NEW -j ACCEPT

#############################

#         OUTPUT            #

#############################

# On laisse tout sortir sur la carte interne (voir les règles suivantes pour la carte externe)

# We let everything out on INTIF (see following rules for the EXTIF)

$IPTABLES -A OUTPUT ! -o $EXTIF -j ACCEPT

# Si configuré, on autorise les requêtes DHCP

# Allow DHCP requests if configured

public_ip_mask=`grep ^PUBLIC_IP= $CONF_FILE|cut -d"=" -f2`		# ALCASAR WAN IP address

if [[ "$public_ip_mask" == "dhcp" ]]

then

	$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport 67 -j ACCEPT

	$IPTABLES -A OUTPUT -o $EXTIF -p udp --dport 67 -j ACCEPT

fi

# On autorise les requêtes DNS vers les serveurs DNS identifiés

# Allow DNS requests to identified DNS servers

$IPTABLES -A OUTPUT -o $EXTIF -d $DNSSERVERS -p udp --dport domain -m conntrack --ctstate NEW -j ACCEPT

# On autorise les requêtes HTTP et HTTPS avec log Netflow (en provenance de E2guardian)

# HTTP & HTTPS requests are allowed with netflow log (from E2guardian)

$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport http -j NETFLOW

$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport http -j ACCEPT

#$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport https -j NETFLOW # When E2guardian will be in HTTPS transparent proxy)

$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport https -j ACCEPT

# On autorise les requêtes RSYNC sortantes (maj BL de Toulouse)

# RSYNC requests are allowed (update of Toulouse BL)

$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport rsync -j ACCEPT

# On autorise les requêtes FTP

# FTP requests are allowed

modprobe nf_conntrack_ftp

$IPTABLES -t raw -A OUTPUT -p tcp --dport ftp -j CT --helper ftp

$IPTABLES -A OUTPUT -o $EXTIF -p tcp --dport ftp -j ACCEPT

$IPTABLES -A OUTPUT -o $EXTIF -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT

# On autorise les requêtes NTP

# NTP requests are allowed

$IPTABLES -A OUTPUT -o $EXTIF -p udp --dport ntp -j ACCEPT

# On autorise les requêtes ICMP (ping)

# ICMP (ping) requests are allowed

$IPTABLES -A OUTPUT -o $EXTIF -p icmp --icmp-type 8 -j ACCEPT

# On autorise les requêtes LDAP

# LDAP requests are allowed

$IPTABLES -A OUTPUT -o $EXTIF -p tcp -m multiport --dports ldap,ldaps -m conntrack --ctstate NEW,ESTABLISHED -j ACCEPT

$IPTABLES -A OUTPUT -o $EXTIF -p udp -m multiport --dports ldap,ldaps -m conntrack --ctstate NEW,ESTABLISHED -j ACCEPT

#############################

#       POSTROUTING         #

#############################

# Traduction dynamique d'adresse en sortie

# Dynamic NAT on EXTIF

$IPTABLES -A POSTROUTING -t nat -o $EXTIF -j MASQUERADE

#Sauvegarde de la marque associée à la connexion pour le load balancing

$IPTABLES -A POSTROUTING -t mangle -j CONNMARK --save-mark

#############################

#          FAIL2BAN         #

#############################

# Reload Fail2Ban

if systemctl -q is-active fail2ban; then

	/usr/bin/fail2ban-client ping &>/dev/null && /usr/bin/fail2ban-client -q reload &>/dev/null

fi